ARM CORTEX Evaluation Boards

ARM CORTEX 1768 Evaluation Boards : ARMCTXM3-01 LPC 1768 ARM CORTEX | ARMCTXM3-06 ARMCORTEX M3

ARMCTX M3-01

ARM CORTEX M31768 Evaluation Board Specifications:-
  • LPC1768 32 Bit ARM Cortex-M3 based processor with 512K bytes Program Flash, 64K bytes RAM.
  • 12MHz Crystal allows easy communication setup.
  • One on board voltage regulator for generating 3.3V. Input to this will be from External +5V DC Power supply through a 9-pin DSUB connector.
  • Reset push-button for resetting the controller.
  • Three of the four controller UART’s are made available to user for external interfaces.
  • – UART0: General purpose RS232 terminated in a 9 pin female DSUB connector which is also used to program LPC1768 Flash memory without external Programmer.
  • – UART1: General purpose RS485 terminated in a 3 pin male reliamate.
  • – UART2: General purpose RS232 terminated in a 3 pin male reliamate .
  • Interface to Controller internal ADC and DAC.
  • 16×2 alphanumeric LCD and 128×64 Graphic LCD display are provided – one of them can be used at a time.
  • 4×4 Key-Matrix.
  • SPI interface: Flash NVROM  memory circuit.
  • Simple I2S demonstration circuit.
  • I2C interface: RTC  IC.
  • Eight general purpose LED’s.
  • Four-digit multiplexed 7-segment display interface.
  • Interface circuit for external Interrupt.
  • Interface circuit for Capture & match.
  • Interface circuit for PWM with a monitor LED.
  • On-board stepper motor, DC motor control, Relay interface.
  • Interface circuit for on board Buzzer.
  • Some of the on board interfaces connect to the Controller using short standard 10 pin FRC cables while the others are connected directly.
  • Standard JTAG connector with ARM 2×10 pin layout for programming/debugging with ARM-JTAG.
  • Standard Emulation Trace connector with 2×10 pin layout for CPU Execution tracing.
  • One standard 26-pin FRC connector to connect to some of ALS standard External Interfaces.

ARMCTX M3-06

ARM CORTEX M3 1768 Evaluation Board Specifications:-
  • LPC1768 is ARM Cortex M3 based micro controller with
    512KB flash memory and 64KB SRAM In-System Programming (ISP) and In-Application Programming (IAP) capabilities.
  • Single 3.3 V power supply (2.4 V to 3.6 V).
  • 70 General Purpose I/O (GPIO) pins with configurable pull-up/down resistors, open drain mode, and repeater mode.
  • Standard JTAG test/debug interface as well as Serial Wire Debug.
  • 12MHz Crystal allows easy communication setup.
  • One on board voltage regulator for generating 3.3V. Input to this will be from External +5V DC Power supply through a 9-pin DSUB connector.
  • Piggyback module containing LPC1768 controller.
  • Standard JTAG connector with ARM 2×10 pin layout for programming/debugging with ARM-JTAG.
  • Reset push-button for resetting the controller.
  • One RS232 interface circuit with 9 pin DSUB connector: this is used by the Boot loader program, to program LPC1768 Flash memory without external Programmer. Application program can also use this UART for serial communication.
  • DC motor interface with direction and speed control.
  • Stepper motor interface with direction and speed control.

  • 16×2 alphanumeric LCD Display.

  • On chip ADC interface circuit with POT.

  • 8-bit DAC interface.
  • 4×4 Key-Matrix connected to the port lines of the controller.
  • One External interrupt circuit with LED indication.
  • Two-digit multiplexed 7-segment display interface.
  • Interface circuit for on board Buzzer, Relay and Led indication controlled through push button.
  • SPI Interface: 2 channel ADC IC with POT and Temperature sensor.
  • I2C Interface: NVROM IC.
  • Internal PWM terminated in test point and LED.
  • Standard 26-pin FRC connectors to connect to on-board interface or some of ALS standard External Interfaces.
  • A number of software examples in ‘C-language’ to illustrate the functioning of the interfaces. The software examples are compiled using an evaluation version of KEIL4 ‘C’ compiler for ARM.
Microprocessor Trainer Kit Feature

ALS SDA 86MEL 8086

A paragraph describing additional information about your business or services. This is a great opportunity to provide details about services that are not listed in the main services menu.
8086MEL Microprocessor Kit Specifications:-

  • CPU: 8086/88 Operating @ 5MHz in MAX mode with provision for 8087 Co-processor.

  • MEMORY: Maximum of 128KB on board EPROM. Maximum of 64KB on board RAM.

  • Battery: Backup option for RAM.

  • I/O PARALLEL: 48 I/O lines using two 8255.

  • I/O SERIAL: One RS232 compatible interface.

  • TIMER: Three 16 bit counter/timer using 8253.

  • KEYBOARD: External PC-AT Keyboard.

  • DISPLAY: Alphanumeric LCD module (2 line x 16 characters ).

  • BUS SIGNALS:  All Address, Data and Control signals are terminated in 50 pin berg stick for user expansion.

  • PIC: Programmable Interrupt controller using 8259.

  • MONITOR: 64KB of powerful user friendly monitor.

  • SOFTWARE: Software with keyboard and serial modes. The PC KEYBOARD allows users to directly  ASSEMBLE / DISASSEMBLE  Mnemonics for 8086 using the alphanumeric LCD display.

Download Technical Brochure
ClicK To Download brochure

educational trainer Kit

A short description of this service and how it helps clients.

IOT Boards

A short description of this service and how it helps clients.

Service 3

A short description of this service and how it helps clients.

Service 4

A short description of this service and how it helps clients.

Service 5

A short description of this service and how it helps clients.

Service 6

A short description of this service and how it helps clients.

Service 7

A short description of this service and how it helps clients.

Service 8

A short description of this service and how it helps clients.